The board itself is large (12cm x 12cm) and I guess similarities would be drawn against Hardkernels older offerings namely ORDROID-U/X. The major differentiator is the plethora of on-board ports and I/O:
Sadly there's no SATA port but the 50 pin dual header (2.54mm) supports I2C, SPI, ADC, PWM, Serial and I think an LCD interface (haven't verified these are working). The downside is that the I/O is probably 1.8v and sourcing a 3.3v/5v level shifter may not be easy. Furthermore what's unclear is how well these interfaces are supported in the kernel source. The 2.54mm pitch is ideal because the connectors are cheap and readily available. Quite a few of the peripheral ports (wifi, ethernet, SD cards, usb) are driven from 2 USB controllers, a SMC USB4640 and a LAN9514. It will be interesting to see if there are noticeable bottlenecks as the controllers are daisy chained. Audio support is provided by a WM8960, with the board providing a headphone jack and on board microphone. There are also solder pads for connecting a pair of speakers, the WM8960 datasheet indicates 1Watt output.
The board requires a 5v power supply and protection is provided by an on board fuse. By default the board boots from the micro sd slot, apparently it is possible to reconfigure the boot device through DIP switches although I couldn't find any documentation describing the settings. Although not obvious there are a number of LED's populated on both the front and back of the PCB. Once the board is powered 4 bright green LED light up indicating the 4 USB ports are powered. I have no idea of their relevance, however they are an irritation giving the level of brightness emitted. I also noticed some LEDs on the underside of the PCB, again I can't see the purpose as that part of the board is not directly visible.
Another oddity is the location of the 4412 processor, its on the back of the PCB. Giving that the processor probably requires some level of cooling, it would indicate the PCB should be mounted using spacers/pillar so that air can flow to the underside of the PCB. Therefore it is advisable to have some pcb spacers handy if your planning to purchase. Fortunately I located some spare brass hex pillars that matched the mounting holes. I suspect the processor will also require some kind of passive cooling although there are no mounting holes or points to affix one.
To access the serial console you require a USB to TTL Serial Adapter which supports 1.8v these can be difficult to source and expensive.
Currently there is pre-view Android and Ubuntu (no h/w acceleration) images available for download, along with uboot and kernel source. I gave the ubuntu image a quick test, however to do so I needed to set the HDMI resolution to 720P, by default it is set to 1080P in the kernel.
As a quick workaround to set 720p I changed the following line in drivers/media/video/exynos/tv/hdmi_drv.c .
#define HDMI_DEFAULT_PRESET V4L2_DV_1080P60
to
#define HDMI_DEFAULT_PRESET V4L2_DV_720P60
To compile the kernel for ubuntu, you need Sourcery G++ Lite I used 2010.09-50 v4.5.1.
To compile the kernel:
make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- mixtile_garage_ubuntu_defconfig
make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- menuconfig
make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi-
make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- modules INSTALL_MOD_PATH=output
make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- modules_install INSTALL_MOD_PATH=output
To copy the kernel to the ubuntu SD card image (where <drive> is SD card device):
sudo dd if=arch/arm/boot/zImage of=/dev/<drive> bs=512 seek=6144; sync;
To copy the kernel modules, you would do something like this, where <mount path> is the path to SD card rootfs :
sudo cp -r output/lib/modules/3.0.15 /<mount path>/lib/module
The user and password for the ubuntu image is 'ubuntu'. The preview ubuntu image has a default Locale of Chinese, to change this edit /etc/default/locale. You also need to change the Language settings from within the Unity desktop. Select Settings->Language Support.
I did test a HDMI to VGA adapter at 720p and it ran fine against my monitor.
Given this is a fairly new board (albeit using an older processor), there seems to be little support available at present which can make it daunting and challenging at the same time.
I did test a HDMI to VGA adapter at 720p and it ran fine against my monitor.
Given this is a fairly new board (albeit using an older processor), there seems to be little support available at present which can make it daunting and challenging at the same time.
